Membrane Garage full car cover, completely waterproof and breathable - L - SUV/Off-Road

- KEG47543050
Description:

Membrane, waterproof and at the same time vapor-permeable car cover. Waterproof even during heavy rain and at the same time vapor permeable, wicking moisture away from under the cover. A weather-resistant cover made entirely of a highly vapor-permeable membrane. It protects against rain, snow, frost and sunlight (harmful UV) as well as pollutants such as dust, bird droppings and tree sap.

The cover is made entirely of 4-layer material:

-two-layer SPUNBOND

-highly vapor permeable membrane

-single-layer SPUNBOND

Bag material composition:

100% polypropylene (PP)

A car covered with an ordinary cover, standing on a wet surface in a 'bubble of water vapor', is exposed to damage. When a wet substrate evaporates, all the water vapor settles on the car, which can cause major damage to the paint and may also cause mold to form. The car covered with the cover we offer is not exposed to such factors because it allows all water vapor to pass through, evaporating and escaping outside. The car will be safe in our cover. Competitor's covers are often completely tight and do not allow water vapor to pass through, which can be very dangerous for our car and do more harm than good.

Product advantages:

- multi-season product;

- protection against: snow, frost, rain, wind, leaves, tree sap, UV radiation, bird droppings, flower dust;

- protects against: corrosion, fading, matting of paint and chrome elements;

- the material is smooth on the bottom and does not scratch the vehicle;

- covers the entire vehicle, slightly overlapping underneath;

- easy to store and transport - does not take up much space;

- thanks to fastening with a cord and additional elastic straps, it holds the vehicle tightly;

- when the ambient temperature is above zero, it wicks away the moisture accumulating under the cover.

When choosing a tarpaulin, we recommend taking into account primarily the shape and length of the car . The determinant is a photo showing the shape of the car that the cover fits.

1. Please compare the shape of your car with the product photo

2. You should measure your car, paying particular attention to its length.

3. The final dimension is the circumference of the car, measured at the height of the bumper (the circumference of the car cannot exceed the tarpaulin dimension specified in the description - it must be slightly smaller or equal).

The textile material from which the tarpaulin is made will fit both a slightly smaller and larger car of a similar shape and dimensions not exceeding the circumference given above.

1. Place the cover on a clean car with the printed side of the cover facing out.

2. Cross the drawstring cords to form the first splice of the knot, then pull the cords firmly, directing the forces parallel to the rear edge of the vehicle (see figure 2 on the cover's outer label).

3. Tie the turnbuckle cords and check that the knot does not come loose when you pull the turnbuckle.

4. Thread the additional cords through the loops sewn into the lower edge of the cover next to the car wheels and use them to attach the cover to the car rims (do not attach it to the hubcaps).

ATTENTION! A cover that is dirty on the inside should not be used. The cover can only be used on a parked car - it cannot be used when transporting the car on a tow truck.

Dimensions: L
- Length: 430-460 cm
- Height: 146-156 cm

Compatibility Table L SUV/Off-Road
AUDI     Q3
BMW     X1, X3 (E83)
DACIA     Duster
FORD     Kuga, Escape
HONDA     CR-V
HYUNDAI     Tucson, ix35
JEEP     Patriot
KIA     Sportage
LAND ROVER     Freelander
MAZDA     CX-5
MITSUBISHI     Outlander
NISSAN     X-Trail, Qashqai
RENAULT     Koleos
SSANGYONG     Korando
SUBARU     Forester
SUZUKI     Grand Vitara
TOYOTA     Rav4, 4Runner
VOLKSWAGEN     Tiguan
VOLVO     XC60

Below is a report on the vapor permeability test of the membrane from which we produce Membrana Garage covers. The research was performed in an independent, accredited testing laboratory. The test confirms the high vapor permeability of the membrane with a very good result of 0.69 Sd and the penetration of water vapor through the cover membrane at the level of 267.7 grams of water vapor per m2 of the membrane in 24 hours.

Quality and durability confirmed by tests

The durability of tarpaulin covers is determined by their resistance to solar radiation (UV), high temperatures, rain, frost, snow and natural dirt. Our specialists have developed effective methods for testing the resistance of materials to external conditions based on our own long-term environmental tests and the PN-EN ISO 4892-3 research standard . In the Atlas UVtest aging chamber from the USA, each delivery of materials from which Kegel-Błażusiak tarpaulin covers are manufactured is thoroughly examined. Thanks to material quality control and long-term environmental tests, we guarantee our customers that will last several years , even with intensive use. our tarpaulin covers

Functionality and safety confirmed by tests

Good tarpaulin covers should not only protect the car against precipitation, pollution and sunlight, but also be safe. These are our Kegel-Błażusiak tarpaulin covers. Our specialists conduct long-term tests of our tarpaulin covers. The effectiveness of the tarpaulin cover protecting the vehicle against weather conditions is tested, as well as its water resistance, water vapor removal from under the cover, the safety of the cover for the vehicle's paintwork, and the effectiveness of attaching the cover to the vehicle in normal and extreme weather conditions . Only products whose long-term tests have ended positively are manufactured by our company Kegel-Błażusiak.